rules.filter - Input format for filtergen packet filter compiler
INTRO
This file describes the input syntax accepted by filtergen(8) .
BASICS
In general form, a filter rule is described by a direction,
an interface, a target and (possibly empty) sets of
matches and options.
Simple rules will look like:
direction interface match0 .. matchN target;
for example:
"XXX
input eth0 source host1 dest host2 proto tcp dport http accept;
Note that the elements of the rule can be placed in any order, with
the exception that the interface must immediately follow
the direction. Thus, this rule is equivalent to the above (though
perhaps less readable):
proto tcp source host1 dport http accept dest host2 input eth0;
The semicolon separates rules. It is optional before a closing brace
or the end of a file. Whitespace is not significant. Anything after
a hash ("#") on a line is ignored.
DIRECTIONA direction merely specifies whether to match packets being sent or
received. The only two directions available are "input" and "output".
Forwarded packets will pass through both,
INTERFACE This specifies which real or virtual network device to filter. As
far as filtergen is concerned, this is just a text string. It must
be the same as the device name on the target system. Common names on
Linux are "eth0", "eth1", ..., "ppp0", etc. Other systems will have
different naming rules.
TARGET A target notes what we do with a matching packet. Universal
options are accept and drop which, respectively, state
that the packet should be allowed as normal, or thrown away. Some
backends support reject to throw away a packet, but send
notification to the sender that it was denied, masq (on output
rules only) to "masquerade" a packet - alter it so that it appears
to come from the address of the sending interface - and proxy
(and its deprecated alias redirect) to divert a connection via
the local system.
MATCHESThe matches are the meat of the rule. They apply a set of
tests to a packet and decide if this rule will be used to process
it. Available matches are:
source addr-range dest addr-range proto {tcp|udp|icmp|...} sport port-range dport port-range icmptype icmp-type
Matches can be negated by prefixing them with a "!":
input eth0 ! dest 10.0.0.3 reject;
(note than not all backends can support this).
OPTIONSOptions affect the behaviour of the matcher or the target.
Currently implemented are log, which logs packets, local,
which means only to check packets to or from this interface,
forward which means the opposite of local, and
oneway which causes the backend to omit rules which permit
return packets.
The log option can optionally specify a message to log matching
packets with, where the backend supports it:
Note that the oneway option make have no effect when used with
the -l command-line flag on backends which support it.
GROUPING
Because it can get tedious to type:
input eth0 source foo dest bar proto tcp dport http accept;
input eth0 source foo dest bar proto tcp dport https accept;
input eth0 source foo dest bar proto tcp dport nntp accept;
input eth0 source foo dest bar proto tcp sport 1:1023 dport ssh accept;
...
filter allows you to group rules with a set syntax:
input eth0 source foo dest bar proto tcp {
dport http;
dport https;
dport nntp;
sport 1:1023 dport ssh;
} accept;
Matches which accept arguments can also be grouped:
input eth0 source foo dest bar proto tcp {
dport {http https nntp};
sport 1:1023 dport ssh;
} accept;
OUT-OF-LINE GROUPS
It is commonly the case that both hosts and routers have long
lists of similar looking rules to allow traffic between groups
of hosts, as above. What if we had another pair of hosts which
needed a variety of services? We could simply put the rule groups
one after the other:
input eth0 source foo dest bar proto tcp {
dport {http https nntp};
sport 1:1023 dport ssh;
} accept;
input eth0 source baz dest quux proto tcp {
dport {1264 1521 1984 8008 8080 26000};
} accept;
The above generates 11 rules, and every additional port adds
another rule through which packets will pass (well, ones which
don't match any of the above). The first four output rules
have the same source and destination hosts and protocol, and we
know that if it doesn't match those on the first rule, it won't
on the next three, either. Out-of-line groups use this fact to
streamline things somewhat:
input eth0 source foo dest bar [
proto tcp {
dport {http https nntp};
sport 1:1023 dport ssh;
} accept;
];
input eth0 source baz dest quux [
proto tcp { dport {1264 1521 1984 8008 8080 26000}; } accept;
];
Where the underlying system supports it, everything inside the
square brackets is moved into a separate "chain" (in ipchains and
iptables-speak) or "group" (in ipfilter-speak). Thus, any packet
not matching "source foo dest bar" or "source baz dest quux" above
will be checked against only two rules, not eleven.
Note that matches which must appear together, like "proto tcp"
and "sport 12345" need to be either both in the group, or both
out of it.
EXAMPLE
Here's a fairly complete example, for a single-interface machine:
#
# Example filter for (for example) a mail server
#
# Unfortunately, we don't have time to audit the
# communications which go on locally
{input lo; output lo} accept;
# But we want to be a bit more careful when speaking
# to the outside world
input eth0 {
# Sadly, we share a DMZ with Windows machines.
# Don't log their netbios noise
proto {tcp udp} source ournet/24 dport 137:139 drop;
proto tcp {
dport { smtp pop-3 } accept;
dport ssh source ournet/24 accept;
# We don't answer this, but don't want to
# cause timeouts by blocking it
dport auth reject;
log drop;
};
# We don't run any UDP (or other non-TCP)
# services
log drop;
};
output eth0 {
proto tcp {
dport { smtp auth } accept;
log drop;
};
# Outbound DNS is OK
proto udp dport domain dest { ns0 ns1 } accept;
log drop;
};